| Model | ZF-HLA-60H-43 | ZF-HLB-60W-65 | ZF-HLB-60-90 | ZF-HLB-60-110 | customize |
| output
| DC voltage | 43VDC | 65VDC | 90VDC | 110VDC | customize |
| Rated current | 1.4A | 0.92A | 0.66A | 0.55A | customize |
| Rated power | 60W | 60W | 60W | 60W | 60W |
| Ripple&noise | 3000mVAC | 3000mVAC | 2000mVAC | 2000mVAC | 2000mVAC |
| current error | ±3% | ±3% | ±3% | ±3% | ±3% |
| Output voltage range | 25-43VDC | 35-65VDC | 50-90VDC | 60-110VDC | Hold |
| Line regulation | ±2% | ±2% | ±2% | ±2% | ±2% |
| Load regulation | ±2% | ±2% | ±2% | ±2% | ±2% |
| Setup,rise time | 700ms,1500ms(full load) 230VAc/115VAc |
| Hold up time | 15ms / 115VAC, 230VAC |
| Input
| Input voltage | 90-277V |
| Frequency range | 47-63HZ |
| Power factory | PF≧0.98/115VAC, PF≧0.95/230VAC, PF≧0.92/277VAC @ full load |
| Total Harmonic distortion | THD< 20% (@ load≧60% / 115VAC,230VAC; @ load≧75% / 277VAC) |
| Efficiency | 90% | 91% | 92% | 92% | 91% |
| AC current | 0.64A / 115VAC 0.32A / 230VAC 0.3A / 277VAC |
| Inrush current | COLD START 55A(twidth=265μs measured at 50% Ipeak) at 230VAC; Per NEMA 410 |
| Leakage current | <0.75mA / 277VAC |
| Protection | Over current | Constant current limiting, recovers automatically after fault condition is removed |
| | Short circuit | Hiccup mode, recovers automatically after fault condition is removed |
| | Over temperature | Shut down o/p voltage, re-power on to recover |
| Environment
| Working Temp. | Tcase= -40 ~ +60℃(Please refer to "OUTPUT LOAD vs TEMPERATURE" section) |
| Max.Case Temp. | Tcase= +80℃ |
| Working Humidity | 20 ~ 95% RH non-condensing |
| Temp.coefficient | ±0.03%/℃(0 ~ 60℃) |
| Vibration | 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes |
| Safty and standards | Safty standards | EN 61347-1:2008+A1:2011+A2:2013 , EN 61347-2-13:2006 , EN 62493:2010 |
| Isolaton resistance | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH |
| Withstand voltage | I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC |
| Others | MTBF | ≥150Khrs MIL-HDBK-218F(25℃) |
| Dimension | 82.8*52*34mm |
| Packing | 0.11kg/pcs 50pcs/5.5kg |
| Note | 1.If have no special requirements,all the input voltage is 230VAC,It was being tested under the condition of 25℃ 2.Ripple and Noise Measurement Methods: Using a 0.5²mm twisted pair, while the terminal to be parallel 0.1uf and 47uf capacitor, measured at 20MHZ bandwidth 3.Safety Design TUVEN61347-1, EN61347-2-13, IEC / EN60968-1.2004 + A1: 2006 |
